格魯夫溫馨提醒:您如需要CAD圖紙或3D模型請聯係格魯夫在線客服或者在谘詢反饋欄目留下您的信息和所需要的具體型號,我們會及時發送給您!

公司新聞

格魯夫減速機使用說明書

Www.Gelufu.Com 格魯夫機械 2015-05-25 18:12:11  點擊:

詳細使用說明書下載

安裝要求 
      1、底座式安裝,應校準中心線標高,聯軸器聯接時,應校準兩軸的同
軸度,柔性聯軸器聯接時浮動量不超過聯軸器的允許範圍,剛性聯接時須保
證各安裝聯接的形位公差。
       2、法蘭式安裝,止口應配合良好,法蘭式安裝並配空心軸聯接時,特
別應保證聯接的形位公差。
       3、扭力臂安裝,主動的空心軸與被動軸應配合良好,被動軸的浮動或
設備振動應小於彈性塊允許的範圍,力臂應固定並鎖緊。
       4、輸出軸加裝聯軸器、皮帶輪、齒輪、鏈輪等件時,請勿重擊,應用
輸出軸外端螺孔,壓入聯接件。皮帶輪、齒輪、鏈輪、攪拌式還需考慮徑向
力。
       5、空心軸與實心軸聯接時(配合公差H7/h6),應塗防鏽油。
       6、準備剛性好的基礎或牢固的台架來安裝傳動設備,同時也需充分考
慮即使加上 大載荷也不至於改變裝配好後備部件的位置。
       7、安裝升降機時,台架麵上的孔,在滿足絲杆能方便通過的前提下,
應盡可能小。
       8、安裝螺栓一般情況下采用8 8級,如果高溫或振動衝擊等情況,請
打圓柱銷以免鬆動。
1.Choosing foot-mount,the height of center line should be calibrated,
choosing coupling—connect,coaxiality should be calibrated,choosing flexible
coupling,run—out should keep within permissible values,choosing rigid
coupling contour and position tolerance should be guaranteed.choosing
long coupling.,rigidity of shaft should be enough
  2. Flange—mount,protruding or concave steps should inosculate with
 housings,using hollow shaft.contour and position tolerance at connection
 parts should be guaranteed
  3 .Torque-arm-mount,hollow shafts should be fit with working shafts,
run out of working shafts and vibration of units should be within ranges of
vibration values torque arm should be fixed and locked
  4. Installation couplings belt wheels.gears,chain gear on output shafts,
please use screw hole in shaff end to press them in the correct position(see
following pictures)and radial force should be considered in case of belt
wheel Chain gears and agitation mode
  5. When connecting hollow shaft and solid shaft.please clean the
surface and put anti—corrosive oil on it
  6. Please choose foundation with good rigidity or stable plat form to
install transmission devices in the meantime.also should take full
consideration that the positions of all parts will not change even if maximum
torque is loaded on units
  7. When installing screw Jacks,the screw holes ln mounting plate
should be as small as possible up to bolts’diameten
  8. Generally fixing bolts adopt GBT8.8 in case of high temperature and
vibration,please take anti—loose measures The tightening torques of
 binding bolts as follows
潤滑及密封 
 1、密封性:骨架雙唇油封屬於易損件,由於使用條件的較大差異,骨
架油封的使用壽命很難確定,失效後須及時更換並補充新油。
       2、潤滑油:減速機一般采用油池飛濺潤滑。對環境溫度高於40'C或減
速機工作時溫度超過1 00℃時應采用循環油潤滑。油池潤滑的油麵高度,規
定當減速器靜止不運轉時,油麵控製在圓油標中心以上的位置。
*擺線類減速機小機型(x4以下)采用油脂潤滑,建議采用4#二硫化鉬鋰
基脂,出廠時機內已加滿。中等以上機型(×5以上)采用油浴循環潤滑,
建議采用50#機械油或90#工業齒輪油,出廠時未加,用戶在開機前應接油
標注入潤滑油。
*MB無級變速機必須使用Ub-3牽引液。
*蝸輪絲杆升降機一般采用3#二硫化鉬鋰基潤滑脂。
    以上所選用的潤滑油可以滿足一般使用要求。若有特殊要求或有經驗的
用戶,可另行選擇其它牌號的潤滑油。環境溫度低時應降低牌號。
一般來說,潤滑油牌號由小增大時,對減速機性能有如下影響;
A、溫度升度,線速度高時程度較明顯;    B、效率降低;
C、噪聲降低;D、密封性能加強;  E、蝸輪或齒輪承載能力增加。
    3、新機在使用動轉400小時後,應更換一次潤滑油並清理內部油汙。
以後的換油周期在正常情況下為:變速機專用油2000小時;齒輪油8000小
時。使用環境惡劣或8小時以上連續工作製的場合,應縮短換油時間。
    4、嚴禁不同品質的潤滑油混合使用。因為混合使用時可能發生化學反
應從而降低或失去潤滑作用
1 Sealing:The two·lip seal belongs to wearing parts;it's difficult to
decide the useful time because of the different condition of the use
condition,affer invalidation,updating new oil timely
  2 Lubrication:generally,gear units should adopt splash lubrication It
should adopt circulation oil if the ambient temperature above 40℃or
 reducer working temperature above 100℃ The grease surface splash
lubrication should be above the center of oil scale when the reducer keep
still
*R、F、K、T、H、B係列齒輪類減速機的潤滑一般采用中負荷工業齒輪油,
牌號見表1
*Genemlly R F K T H B Series gear reducer is adopts the moderate
lode industrial gear oil.check the oil number on table 1
*The small type of Cycloid reducer(under X 4)adopt grease lubrication.
you’d better adopt number 4 molybdenum disulphide grease all machines
have enough lubrication before leaving factory Above middle type
(above X 5)adopt lubrication by oil circulation,you’d better adopt number
50 rnachinery oil or number 90 industry gear oil No oil before leaving
factory,users have to fill oil before the machine start up
*MB Speed variator must use UB一3 traction liquid
*Worm screw Jack must use number 3 molybdenum disulphide grease
  The lubrication,which selected can satisfy the ordinary require If there
is special require or experienced user can use other oil choose the low
number oil when the ambient temperature is low
Generally.the lubrication influence the reducer when the lubrication
number increasing as the following:
A When the temperatures increase and linear velocity
B Efficiency decrease
C Noise decrease
D Leak tightness increase
E Carrying capacity of worm and gear increase
  3 Newmachineworking after 400 hours the oil should be changed and
removethe deposits and old oil The replace cycle:oilofvariator:2000 hour.
Gear oil:8000 hour.The vile using environment or over 8 hours continuous
work—places should shorten the time for oil
  4 Different lubrication using mixed is prohibiting strictly,it may reduce
the efficiency of the lubrication for the chemical realign
使用養護: 
 1、開機前應檢查機內油麵是否符合要求,按提示鬆開或挽上通氣糟使
之通氣順暢,並檢查轉動是否靈活。
    2、負載試車前要空載運行半小時左右,確認空載無故障後方可加載運
行。試車應經常檢查運轉情況:不得有異常衝擊,振動,不得滲、漏油,溫
升不得超過60℃, 高油溫不得超過100℃(日常工作時也應進行檢查)一
切正常方可正式工作。
    3、工作中發現異常情況應停機檢查,查明、排除故障後方可繼續工作。
時常檢查潤滑油情況,注意補足油量,及時更換變質的潤滑油。
    4、若出現安裝方位變動,一般情況下調換油鏡、油塞、通氣帽即可。
    5、減速器應經常保持清潔,外表麵不得堆積灰塵、髒物以免影響散熱。
    6、貯存:在幹燥通風、室溫環境中存放。當貯存期超過三個月時應作
防鏽處理。放置一年左右的機器,使用時要檢查油封是否老化,油品是否變
質。
1 Checking the oil level if it's in line with the require before the machine
is running,loose or change the vent cap for ventilate unhindered and
checking the rotating if it's flexible or not
  2 It should be running unloaded half an hours before running loaded,
checking the running condition on trial fun;no exceptional shock,percussion
 No oil leak The temperature is limited to 60℃ the oil is limited to 100 ℃ (it
should be checking in routine work as well)it can be running until everything
is standing by
  3 It must be stopped immediately for check once any problem during
 running gear units,check the condition of the oil fill the oil,change the
lubrication when it’s deteriorated
  4 If mounting position changed,the position of breathe screw Oil level
Oil drain plug will be change with each other as usual
  5 Gear units should be keeping clean No dust accumulated on the
surface in case of influencing radiator
  6 Store it in the environment of dry ventilate and room temperature
when the storage time exceed 3 months,treat it with rustproof,check 
the oilclosure and oil whether it had gone bad when the machine is 
placed for l year
關鍵詞: 減速機 升降機
在線留言
    提交留言
    在線客服